PERMACOAT 3000

Industrial Floor Coating

Chemical Resistant Floor Coatings

Description

PERMACOAT 3000 is a 100% solids, zero VOC, industrial floor coating.
PERMACOAT 3000 can be utilized as a glaze coat for the PERMATEC high build floors, or as a multi coat flooring or containment system (30-125 mils). When applied as a multi coat floor or containment system, a silica broadcast is used between coats.

PERMACOAT 3000 consists of two components, resin and hardener, in both the horizontal and vertical formulations. Its application is accomplished with rubber squeegees and short nap paint rollers.

Function

PERMACOAT 3000 is designed as a heavy duty (30-125 mils) industrial floor coating and/or secondary containment system where moderate mechanical abuse and chemical exposure are anticipated.

PERMACOAT 3000 can be installed over most sound floors, including old or new concrete, steel and wood, providing a cost-effective alternative to high-build floor toppings.

Typical Applications

  • Food processing plants
  • Chemical processing plants
  • Breweries
  • Pulp & paper mills
  • Laboratories
  • Processing areas in general where chemicals are used
  • Any area that requires a safe, non-slip floor

Features

PERMACOAT 3000 allows for a fast, easy application. It also offers chemical resistance and physical performance much higher than those found in paints and other thin mil coatings.

NOTE: At 30-50 mils, PERMACOAT 3000 provides excellent chemical resistance for splash and spill exposures. In addition, when applied at 50-80 mils, it can often be recommended for containment service. (For specific recommendations, refer to the "Chemical Resistance Guide" and your local distributor.)

Other Features Include:

  • - Rapid cure resulting in minimal downtime
  • - Odor free
  • - Non-skid safety finish optional

Typical Properties

Solids, by Volume

100%

Hardness (Shore D)
ASTM D2240

82-85

Flexural Strength
ASTM D790

16,500 psi

Tensile Strength
ASTM D307

11,000 psi

Bond Strength to Concrete
ASTM D4541

Exceeds Tensile Strength of concrete. Failure in Concrete.

Taber Abrasion
ASTM D4060
CS 17 Wheels

Loss/1000 cycles = 25mg

Packaging and Coverage

PERMACOAT 3000 is packaged in one and three gallon units. Each unit consists of pre-measured components, Part A (Resin) and Part B (Hardener).

Application thickness may vary from 30-125 mils, depending on the expected service conditions. Factors to consider are 1) length of chemical exposure, 2) mechanical abuses, and 3) substrate texture.

Cure Time

The cure time of PERMACOAT 3000 and other resinous systems are very dependent upon the temperature of the substrate. The chart below represents the approximate times for the respective service conditions, following the last coat:

Service (hours)

70F

80F

90F

Foot Traffic

10

8

6

Light Chemical

14

12

10

Fork Lift

20

16

12

Mixing

Prior to application of PERMACOAT 3000, the resin, hardener and substrate should be between 70 degrees F and 95 degrees F.

Premix the Resin (Part A) for 30 seconds using a Jiffler mixer blade attached to a 500-750 RPM drill. Add the Hardener (Part B) only when the batch is ready to be applied. Mix for approximately 90-120 seconds. After mixing, pour immediately onto the floor.

Application

Use a rubber squeegee to spread the resin over the pre-measured area to be covered. Immediately back roll the PERMACOAT 3000 with a short nap (1/8 inches) wool or mohair roller. At this point, several pre-specified readings should be made with a wet mil gauge to assure uniform coverage. After the coating has been back rolled and uniform thickness verified, the surface should be saturated with a silica broadcast.

After the first coat supports foot traffic, the excess silica can be removed. Within 24 hours a second coat of PERMACOAT 3000 should be applied using the same procedure, minus the silica broadcast.

NOTE: Additional broadcasts and roll-coats can be utilized to increase floor thickness.

Clean-up

All mixing and application equipment should be cleaned immediately after use. If this is done, soap and water or biodegradable cleaners can be used. If the material has begun to set, more aggressive solvents will be necessary. Before using solvents, refer to their respective SDS for handling considerations.

Maintenance

For systems designed for splash and spill exposures, routine wash downs are recommended to reduce the length of chemical exposure. This step is not necessary where the product is recommended for containment service.

Storage and Shelf Life

PERMACOAT 3000 should be stored at 50-90 degrees F out of direct sunlight. All containers should remain unopened until ready for use. If stored as set out above, PERMATEC 3000 has a minimum shelf life of one year.

PERMACOAT 3000 should not be applied over substrates:

Where Permacoat 3000 Should Not Be Installed

  • subject to hydrostatic pressure
  • which are unsound
  • which are contaminated and cannot be cleaned
  • at temperatures below 70 degrees F (Consult ChemProof Polymers)
  • which are wet during the application

Safety

PERMACOAT 3000 contains blended Epoxies as the resin and blended Amines as the hardener. Protective clothing and gloves are recommended to prevent sensitization to these materials. In case of ingestion or eye contact, it is advisable to contact a physician immediately. SDS are available for this product upon request.

Warranty

For product warranty see ChemProof Polymers, Inc. "Standard Limited Warranty". If one is not included with this literature, contact your local distributor or ChemProof Polymers, Inc. for a copy.

Related & Ancillary Products

PERMATEC 4000
Modified Epoxy Floor Topping

PERMATEC 5000
Modified Epoxy Floor Topping

PERMAGROUT E
Epoxy Grout/Resurfacer

PERMAFLEX 1100
Flexible Epoxy Underlayment

Related Vertical Products

Contact Information

ChemProof Polymers, Inc.
Industrial Floor Coatings
2750 Charles Page Blvd.
Tulsa, OK 74127
Phone: 918-584-0364
Fax: 918-584-0366